If the power light blinks in a neverending way, the 30/30/30 reset has no effect. This procedure is usually called 30/30/30 reset. Disconnect power cord for another 10 secs and then reconnect.Release the reset button and give the router about 10 secs to resettle.Still hold the reset button for another 30 secs.Hold the reset button for another 30 secs.Without releasing reset button, disconnect power cord.Disconnect the router from UTP cables (not the power cable).To determine if the router is bricked, carefully follow the steps at note 6 of the peacock thread: īefore you continue below, make sure you've first tried a hard reset to revive your router: These techniques may be useful in these cases also. It is also unfortunately possible to configure your router in ways which make it dead to the world. Don't worry, there are a number of things you can try to get your router working again before giving up and living with the fact that your router is now a paperweight. So, you're afraid you've bricked your router. Read the text files here, and also see this relevant forum post for newer instructions.THIS IS AN OLD PAGE THAT MOSTLY APPLIES TO BROADCOM MIPSR1 AND MIPSR2 ROUTERS MORE UP TO DATE INFORMATION CAN BE FOUND AT NOTE 6 OF THE PEACOCK ANNOUNCEMENT (LINKED BELOW) AND THE WIKI ARTICLES ON SERIAL RECOVERY AND JTAG. Historical information: All flash chips are supported, follow this procedure. bin file location worked, but had to hit enter TWICE to execute the command to install the 2nd bin file: With this procedure (external link), using this command from the. bin file I installed from the Linksys GUI Admin options, upload went about half way then tried to reboot, and bricked my WRT54GSv7. This will time out repeatedly, then the router will respond about two and six times, time out again a few times, and then start responding to pings. Start a continuous ping: ping -t 192.168.1.1 (-t is Windows only) Linux: enter tftp mode with # tftp 192.168.1.1ĥ.Use the web inferface to update the firmware to vxworkskillerGSv7-v3.bin.Ĥ. 192.168.1.10 or any address outside the DHCP range)ģ. Use the web interface to reset the router to factory defaults.Ģ. If you leave tftp in ascii it will appear to work but the flash won't take.ġ. Messing around with JTAG cables taught him some things, but be absolutely sure that you have tftp set to binary or octel. He felt that he had bricked one of the routers at first. Tiger12506 has successfully performed this on two WRT54GS v7.2 with CGNE serial numbers. My WRT54GSv7.2 has an EON EN29LB160AB-70TCP flash chip and 16MB Samsung RAM. This method has also been used on WRT54Gv8 (not GS), and should work on the v7.0. There is no resetting in the middle of this process. Note: If the router does not boot automatically, even after a power cycle, reset again, per step 3.Watch the router lights: the power light will eventually come on, followed by the WLAN light.Wait for tftp to finish, then the router will automatically reboot.Windows™ Command Prompt (cmd): tftp -i 192.168.1.1 put dd-wrt.v24_micro_generic.bin.Linux command: tftp -v -m octet 192.168.1.1 -c put dd-wrt.v24-micro_generic.bin.Wait for FIVE FULL minutes, then disconnect the power cord for 10sec and reconnect it.After the dialogue about disconnecting the power cord is shown, disconnect the power cord and reconnect it.Use the Firmware upgrade option under the Administration tab to flash vxworkskillerGSv7-v3.bin.Unplug the router, then hold the reset button while reconnecting power for about 20 seconds.Ensure this static IP is outside the DHCP range.Select "Use the following IP address" to set a static IP (e.g.Right-click, go to the LAN device properties, then find and open the TCP/IPv4 Properties. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |